The IC-6T packs proven materials and technology into a installer-friendly, UL-certified loudspeaker with an integrated back can and multi-tap transformer.

The two-way IC-6T features a swiveling Tractrix® Horn with aluminum dome compression driver, which allows contractors to direct the sound to specific areas more accurately than fixed position tweeter designs, minimizing disturbing sonic reflections even when the speaker is positioned in a less-than-optimal locaton. Other features include an injection-molded woofer cone, Santropene® surround, cast polymer woofer frame and screw-down terminals.

As a benefit for distributed line applications, the IC-6T features a 60-watt 70/100 volt multi-tap transformer. A single switch for the 8-ohm bypass and multi-tap setting is conveniently located on the front baffle. The IC-6T is shipped complete with a tile bridge for installation in a suspended ceiling or wherever additional reinforcement of the ceiling material is required.

Put the finishing touches on any great commercial sound system with the new CA-SW-8T all-purpose, indoor/outdoor subwoofer. This compact and rugged passive subwoofer with an internal multi-tap transformer nicely complements the Klipsch CA-Series and other small to medium sized full-range speaker installations by adding high-impact, robust bass.

The CA-SW-8T shakes things up and delivers a deep, driving sound through an 8-inch, long excursion driver that has a high-temperature voice coil attached to an IMG (injection-molded graphite) cone that combines light weight, excellent rigidity, and water resistance. As a result, this ported subwoofer is capable of high output while remaining extremely reliable. Maximum continuous output is a remarkable 111dB SPL. And since AES rated sensitivity is 92dB, adequate levels can be achieved with modest amplifier power using the CA-SW-8T.

This durable subwoofer's paintable, weather-and UV-resistant ABS plastic enclosure and powder-coated aluminum grille facilitate easy placement in harsh, outdoor environments. For distributed sound system applications, the internal multi-tap transformer allows 70-volt, 100-volt, or pass through 6 ohm operation.

Five-way, binding-post inputs simplify connections, and there is a fixed, low-pass crossover at 150Hz. For easy wall or ceiling mounting, the CA-SW-8T comes with a C-bracket assembly that attaches to threaded studs in the cabinet with oversized knobs, ensuring positive lock. And at just 19 pounds, this subwoofer is easy to adjust for optimal coverage.

Built from the inside out for performance and durability, the CA-SW-8T adds warmth and body to commercial sound systems.

Architectural Specifications

The CA-SW-8T passive subwoofer system shall include an 8-inch weather-resistant IMG-cone driver. Signal shall be provided to the transducer via a passive internal low-pass filter with a 12dB/octave slope above a 150Hz cutoff frequency. The enclosure tuning shall be bass reflex.

The frequency response shall be 51Hz to 135Hz, +/-4dB, with the -10dB point at 42Hz, measured at three meters, half space anechoic. Sensitivity shall be 92dB SPL, measured at one meter, half space anechoic, with a 2.83V input. Power handling shall be 150 watts (25V), to AES standards, continuous pink noise, 50Hz to 10kHz, 6dB peaks. Calculated maximum continuous output at one meter shall be 111dB SPL. Nominal impedance shall be at 6 ohms with a 4 ohm minimum at 92Hz. Connections shall be made via 5-way binding posts.

A removable powder-coated aluminum grille shall be provided for protection of the transducer from tampering or damage. The enclosure shall be of UV- and weather resistant ABS plastic, available in black or white, with dimensions of 11.125" (28.26cm) high by 16.375" (41.59cm) wide by 11.75" (29.85cm) deep. Net weight shall be 19lbs. (8.6kg). Mounting shall be via protruding stainless steel threaded studs on the side enclosure panels, mating to large external knobs for positive attachment to the C-shaped mounting bracket (included).

The system shall be a Klipsch CA-SW-8T subwoofer.

Built from the inside out for performance and durability, the IC-8T-SW packs a lot of substance into commercial sound system.

Most distributed audio systems are plagued with thin-sounding performances, but the new IC-8T-SW in-ceiling subwoofer changes everything. Engineered for music reinforcement applications, these unobtrusive, easy-to-install loudspeakers feature a transformer-less design for 70.7V/100V distributed-line systems. Since transformers severely limit a subwoofer's capabilities, this unique design is the perfect solution when building a great sounding commercial system. 

The IC-8T-SW adds more dimension to any in-ceiling configuration by using an 8-inch woofer, 8-inch drone, polypropylene cones and high-temperature voice coils in the woofer. While most subwoofers use a port to increase output, the IC-8T-SW employs a bandpass design that utilizes a passive radiator. This eliminates a lot of the distortion and minimizes turbulence that is often present in ported designs. Maximum continuous output is a remarkable 111dB. And since AES rated sensitivity is 92dB, adequate levels can be achieved with modest amplifier power using the IC-8T-SW. 

Other key features of the IC-8T-SW include the ability to easily switch from low impedance to high impedance distributed-line applications as well as mono and two-channel inputs in low impedance modes. This durable subwoofer has an ABS plastic baffle, formed steel back can and a four-point terminal strip input connector. The IC-8T-SW is shipped complete with a tile bridge for installation in a suspended ceiling or wherever additional reinforcement of the ceiling material is required. A mudring kit (part # 061347) is also available for drywall ceiling installations.

The IC-5T packs proven materials and technology into a installer-friendly, UL-certified loudspeaker with an integrated back can and multi-tap transformer.

The two-way IC-5T features a swiveling Tractrix® Horn with aluminum dome compression driver, which allows contractors to direct the sound to specific areas more accurately than fixed position tweeter designs, minimizing disturbing sonic reflections even when the speaker is positioned in a less-than-optimal locaton. Other features include an injection-molded woofer cone, Santropene® surround, cast polymer woofer frame and screw-down terminals.

As a benefit for distributed line applications, the IC-5T features a 30-watt 70/100 volt multi-tap transformer. A single switch for the 16-ohm bypass and multi-tap setting is conveniently located on the front baffle. The IC-5T is shipped complete with a tile bridge for installation in a suspended ceiling or wherever additional reinforcement of the ceiling material is required.

The little speaker with the big sound! Ideal for applications where "tight space" under-eave, wall or ceiling mounting is required. The CA-5T full range loudspeaker includes everything you need for fast and easy installation. The durable UV-resistant all-weather enclosure includes an internal multi-tap transformer to simplify hookup to any system. The C-bracket assembly attaches to the enclosure's integral "center-of-gravity balanced" threaded studs and oversized knobs, ensuring a positive position-lock. A security retainer allows for wiring to a second mounting point, guarding against dislodging or tampering.

Designed for distributed audio applications, the compact high-fidelity system is equally at home in outdoor or indoor background music and paging applications, in both commercial and recreational environments. For application flexibility, the internal multi-tap transformer includes an easily adjusted bypass switch, allowing direct full range connection for 8 ohm operation. Enclosure signal connections are accomplished through a 5-way binding post.

For efficiency and reliability, the CA-5T consist of a high power 5.25" weather-resistant woofer and a 1" polymer diaphragm compression driver on a molded Tractrix Horn. A unique feature of the 90º x 60º horn assembly is its ability to be repositioned 90º, providing selectable pattern control.

Power handling and performance efficiency are superb at 75 watts continuous and 94dB sensitivity, with a maximum output of 109dB.

The paintable ABS enclosure is available in black or white finishes, and features all stainless steel hardware and a removable aluminum powder-coated grille for years of maintenance-free duty, no matter the climate or environment.

Architectural Specifications
The CA-5T all-purpose two-way compact loudspeaker system shall include a 5.25" (13.34cm) K-1109-A woofer and a 1" (2.54cm) K-117-A polymer diaphragm compression driver mounted on a Tractrix Horn. Signal shall be provided to the transducers via a passive internal frequency dividing network, with a 2.7kHz crossover frequency. The enclosure tuning shall be dual port bass reflex.

Frequency response shall be 70Hz to 20kHz, ±4dB, with the -10dB down point at 60Hz, measured at one meter, half space anechoic. The dispersion angle shall be 90º by 60º nominal (refer to graph). Sensitivity shall be 94dB spl, measured at one meter, half space anechoic, with a 2.83V input. Power handling shall be 75 watts (17volts), to AES standards, continuous pink noise, 50Hz to 10kHz, 6dB peaks. Calculated maximum continuous output at one meter shall be 109dB spl. Nominal impedance shall be 8 ohms, with a 3.8 ohm minimum at 260Hz. Full-range connections shall be made via 5-way binding posts.

A removable powder-coated aluminum grille shall be provided for protection of the transducers from tampering or damage. The enclosure shall be UV- and weather-resistant ABS plastic, available in black or white, with dimensions of 8.625" (21.9cm) high by 12" (30.48cm) wide, by 8.875" (22.54cm) deep. Net weight shall be 10 lbs. (4.54kg).

Mounting shall be via protruding stainless steel threaded studs on the side enclosure panels, mating to large external knobs for positive attachment to the C-shaped mounting bracket (included).

The system shall be a Klipsch CA-5T loudspeaker.

The Klipsch CA-8T compact full range system is perfect for higher power professional applications where flexible mounting and extended range are required, including everything needed for fast and easy distributed sound installations. Equally at home indoors or out, in foreground or background, higher spl applications, the CA-8T's appearance and Klipsch fidelity fit into residential, business or recreational environments equally well.

The UV- and weather-resistant ABS enclosure includes an internal multi-tap transformer with switchable direct 8 ohm bypass, simplifying hookup to any type of sound system. The C-bracket assembly attaches to the enclosure's integral stainless steel threaded studs with oversized knobs, ensuring a positive position-lock and rapid "no-pain" installation. External attachment to the built-in security retainer provides an extra measure of safety, protecting against unexpected damage or removal.

The CA-8T includes a high power 8" extended range low-frequency driver and a 1" titanium diaphragm compression driver on a molded Tractrix Horn. The 90º x 60º horn and driver assembly allows repositioning by 90º for selectable pattern control.

The compact dual port bass reflex loudspeaker system can handle 100 watts continuous power for an AES sensitivity of 96dB and a maximum output of 113dB spl.

Paintable and available in black or white finishes, the ABS enclosure features corrosion- and rust-resistant stainless steel hardware and a removable aluminum powder-coated grille, ensuring maintenance-free service in any environment or application.

Whether indoors or out, the Klipsch CA-8T is the good looking, great sounding full-range solution for installed high-fidelity sound.

Architectural Specifications
The CA-8T all-purpose two-way compact loudspeaker system shall include a 8" (20.32cm) K-1111-A weather-resistant low frequency driver and a 1" (2.54cm) K-118-A titanium diaphragm high frequency compression driver mounted on a molded Tractrix Horn. Signal shall be provided to the transducers via a passive internal frequency dividing network, with a 2kHz crossover frequency. The enclosure tuning shall be dual port bass reflex.

Frequency response shall be 64Hz to 19kHz, ±4dB, with the -10dB down point at 45Hz, measured at 1 meter, half space anechoic. The dispersion angle shall be 90º x 60º nominal (refer to graph). Sensitivity shall be 96dB spl, measured at 1 meter, half space anechoic, with a 2.83V input. Power handling shall be 100 watts (21V), to AES standards, continuous pink noise, 50Hz to 10kHz, 6dB peaks. Calculated maximum continuous output at 1 meter shall be 113dB spl. Nominal impedance shall be 8 ohms, with a 4.2 ohm minimum at 175Hz. Full-range connections shall be made via 5-way binding posts.

A removable powder-coated aluminum grille shall be provided for protection of the transducers from tampering or damage. The enclosure shall be of UV- and weather-resistant ABS plastic, available in black or white, with dimensions of 11.125" (28.26cm) high by 16.375" (41.59cm) wide by 11.75" (29.85cm) deep. Net weight shall be 17 lbs. (7.72kg). Mounting shall be via protruding stainless steel threaded studs on the side enclosure panels, mating to large external knobs for positive attachment to the C-shaped mounting bracket (included).

The system shall be a Klipsch CA-8T loudspeaker.

Designed for high fidelity distributed sound system installations, the CA-6T compact full range loudspeaker is perfect for foreground or background applications in restaurants, outdoor recreation environments, boardrooms or A/V systems. The rugged ABS enclosure is weather-resistant and UV-resistant for a long service life. An internal multi-tap transformer includes direct bypass switching for distributed or direct 8 ohm operation.

The included C-bracket and integral threaded studs with oversized knobs allow easy under-eave, wall or ceiling mounting for rapid "center-of-gravity balanced" installation. A security retainer provides for secondary attachment to an external safety point, guarding against tampering or drop damage. Connections are provided via 5-way binding posts.

The CA-6T components include a high power 6.5" extended range woofer and a 1" highly accurate titanium diaphragm compression driver mounted on a square-mouth Tractrix Horn. The 90º x 60º horn/driver assembly can be repositioned by 90º to provide flexible horizontal and vertical pattern adjustments.

Providing great sound for its size, the compact CA-6T full-range loudspeaker system is capable of 85 watt continuous power handling, with an AES-rated sensitivity of 95dB and a maximum output level of 111dB spl.

The removable powder-coated aluminum grille and stainless steel hardware offer years of maintenance-free protection no matter the climate or environment. The available black or white enclosure finish can be painted to match surrounding decor.

Inside and out, the Klipsch CA-6T provides superior audio performance in a durable - and flexible - commercial package.

Architectural Specifications
The CA-6T all-purpose two-way compact loudspeaker system shall include a 6.5" (16.5cm) weather-resistant K-1110-A low frequency driver and a 1" (2.54cm) K-118-A titanium diaphragm compression driver mounted on a molded Tractrix Horn. Signal shall be provided to the transducers via a passive internal frequency dividing network, with a 2kHz crossover frequency. The enclosure tuning shall be dual port bass reflex.

Frequency response shall be 69Hz to 20kHz, ±4dB, with the -10dB down point at 53Hz, measured at 1 meter, half space anechoic. The dispersion angle shall be 90º x 60º nominal (refer to graph). Sensitivity shall be 95dB spl, measured at 1 meter, half space anechoic, with a 2.83V input. Power handling shall be 85 Watts (19V), to AES standards, continuous pink noise, 50Hz to 10kHz, 6dB peaks. Calculated maximum continuous output at 1 meter shall be 111dB SPL.

Nominal impedance shall be 8 ohms, with a 4.1 ohm minimum at 180Hz. Full-range connections shall be made via 5-way binding posts.

A removable powder-coated aluminum grille shall be provided for protection of the transducers from tampering or damage. The enclosure shall be of UV- and weather-resistant ABS plastic, available in black or white, with dimensions of 9.5" (24.13cm) high by 15.125" (38.42cm) wide by 10.375" (26.35cm) deep. Net weight shall be 15 lbs. (6.81kg). Mounting shall be via protruding stainless steel threaded studs on the side enclosure panels, mating to large external knobs for positive attachment to the C-shaped mounting bracket (included).

The system shall be a Klipsch CA-6T loudspeaker.