Paul W. Klipsch

Legendary knowledge.

In 1978, Paul W. Klipsch was awarded the Audio Engineering Society's second highest honor, the prestigious Silver Medal, for his contributions to speaker design and distortion measurement. Mr. Klipsch was inducted into the Audio Hall of Fame in 1983. In 1997, he was inducted into the Engineering and Science Hall of Fame, an honor shared by Thomas Edison, George Washington Carver and the Wright brothers.

While perhaps we all can't be so brilliant, we can certainly do our part to pass along nuggets of his genius, as well as basic audio info for the layperson. Which is why we have this section of our website. Use the search form below to enter some keywords based on what your are looking for.

Happy learning!

 

Search Results

Didn't find what you were looking for? Try using a wildcard. Example: rp-2* will return anything that has text that starts with "rp-2".

  • How do I set subwoofer phase?

    Depending on the absolute phase of your main speakers and amplifier and the distances of the subwoofer and the main speakers from the listening position, the bass in the crossover region may be smoother if you reverse the subwoofer’s phase. Typically, though, phase is left at 0° for most applications.

    While seated in your listening sweet spot, play music with bass content that is familiar to you and then have someone switch the 0/180 phase switch on the sub to 180-degrees. This will let you determine if the bass sounds louder in your seating position. The more bass-heavy setting is where the output of the subwoofer and the main speakers are most in phase. Use whatever position (0/180) is louder at your seating location. (Note: some subwoofers may contain a “variable” phase control, which provides variable control between 0 and 180 for even more precise phase control of your subwoofer.) However, if you do not notice any difference when changing the 0-180 setting, it only means there are no issues in your room and all is fine.

  • The back of the subwoofer is warm. Is this normal?

    A subwoofer will run warm when in use, by design. However, it should not be uncomfortable to leave your hand on the back panel for 5 seconds.

  • Can I put more than one subwoofer in my room?

    Sometimes, adding a second subwoofer can smooth bass response throughout the room. This is due to h3 acoustic standing waves in the room which are dependent on the basic room dimensions (height, length, and width) and the placement of the sub and primary listening area. With a single sub, it is possible to obtain h3 bass at one spot, with very weak bass elsewhere in the room. You can hear this by carefully listening to bass as you move a few feet in any direction. If you have h3 bass/weak bass problems, using a second sub in a different location may reduce the severity of the problem. The important thing to remember is to find what sounds best to you! Each room is different; experiment until you find the placement that produces the most pleasing bass to your ears. 

    Some people feel they can never have enough bass. So long as they are placed properly, multiple subwoofers typically produce more bass. It is important to note that unless the second subwoofer goes deeper than the first one, adding additional subwoofers will only raise the bass volume—it will not produce deeper base. You’ll need to experiment with different positions (as previously described) to find the best places for two or more subwoofers. Some people use one subwoofer for a certain frequency range and the second for another (such as the LFE channel in 5.1 recordings). Other options are to connect one subwoofer to the front channels and one to the rear channels, or one to the center channel and the other to the remaining channels.

  • Can I program a “learning” remote to operate my subwoofer?

    Although Klipsch has provided download files for remote control operation, we do not officially support any remote control issues. Our tech support group has not programmed any learning remotes to function with the RT series; they do, however, provide the IR codes. Any issues that might arise concerning the programming of remotes would be technical support issues for the individual remote control manufacturers.

    Codes for the Phillips Pronto, RTI, and Universal Remote controls are not “read text” files. Unless your remote is programmable via PC, it’s unlikely these will be of any use. If your remote is not one of these brands, you should still be able to obtain files to program them. (See below) To use our codes, unzip them to your hard drive and connect the remote via cable to your computer; the codes are downloaded directly into the remote.

    For example, to program UEI manufactured remotes, go to http://www.uei.com. Under products, you should see One-For-All, Kameleon and Nevo. The code should work, once you use a standard number code (1991) to program. In theory, after you have a working remote, a learning remote should be able to "learn" the codes from the programmed unit, just as it would for any other remote.

    Logitech has the codes for all Harmony remotes for the Klipsch model subs noted below. All Harmony remotes should accept the same programming. Add the device from the Harmony software in the following manner. http://www.logitech.com

    Add “Device”, choose “Amplifier”, choose “Amplifier” the second time, choose “Klipsch” from the manufacturers’ listing and type in the model precisely as they are below for the model you own:

    • RW-10d 

    • RW-12d 

    • RSW-10d 

    • RT-10d 

    • RT-12d

  • Where is the best place to put a subwoofer in my room?

    It is generally believed that the bass you hear below approximately 80 Hz is non-directional. This means that you can point the loudspeaker in any direction and the sound will still reach the listener's ears. Since much of the bass that subwoofers produce is below that frequency, you can place the subwoofer almost anywhere in the room. This is the opposite of full-range speakers, which have just a few placement options in a room that allow them to sound good, since they must be positioned for the best combination of imaging and tonal balance. Putting a subwoofer in a corner of the room may cause the sub to sound louder. If your subwoofer is a ported design, keep it at least twice the diameter of the port exit (probably 6-12 inches) away from the nearest wall, so that air flowing out of the port is not obstructed. If the bass seems too boomy, you can fine-tune the sub by moving it farther from the wall until it sounds smooth to your ears. 

    The best way to find the ideal place for your subwoofer is to hook it up and put it right where you will be sitting in the room. Set the subwoofer to level, low pass and phase. Play something with consistent, deep bass and move around the room on your knees; this way your head is about where it would be when you are seated. The spot where the bass sounds best is a spot where you might put your subwoofer. You may find more than one location. 

    Corner placement of the subwoofer typically yields the loudest output (highest efficiency). This does not mean that it will always sound best in this position; experimenting with placement is always suggested. It's also important to have the sound from the sub reach the listener in sync with the sound from the main speakers; otherwise the sound may not blend properly. You should not be able to hear your subwoofer as a separate entity—it should seem that your main speakers go deeper with greater impact and authority.

  • What is the best way for me to hook up my subwoofer?

    The optimal connection is to use the RCA (Phono) "sub" or "woofer" line out found on home theater receivers and pre-amps. Some subwoofers offer High Level inputs (speaker wire connections), they are there for use with a receiver or pre-amp without a sub RCA connection. You don't need to use both and in most cases it's not recommended. 

    Just as receivers and preamplifiers are different across brands, subwoofer brands may be different as well. Every room may be unique in the way it supports or cancels low frequency information. The quantity of bass desired may differ for each listener. Additionally, hookups to the same amps or receivers and the same subwoofers can produce different results if "bass management" settings (speaker size selectors, etc.) or subwoofer settings are different. The best thing to do is to experiment until it sounds just right for your listening style. 

    In some rare cases, you may find an RCA connector marked LFE (Low Frequency Effects) on a receiver or pre-amp; hooking up the "LFE" jacks usually only sends bass special effects of a 5.1- encoded movie to the subwoofer. In that case, when music is played on a two-channel source (for example, a CD), the subwoofer may not receive any signal at all. That situation would call for a hookup of both the "LFE" jacks and the speaker terminal jacks to a subwoofer, in order for the sub to produce bass with all sources. You would need to set the main speakers to "large" in the receiver or pre-amp set-up menu. If you have both LFE and sub out connections on a receiver or preamp, your best choice would be to use the ‘sub out’ connector, because the LFE signal may still be mixed in with the sub channel. 

    Be sure to check the owner’s manual that came with the subwoofer about connecting to both LFE in and speaker wire inputs. With some older subwoofers, this was listed as "optional" and it's fine to connect to both; however with most subs today, this is not recommended, as it may damage the sub electronics. So double-check the manual or contact our tech support department to clarify any questions regarding Klipsch subs. 

    In the end, it comes down to what sounds best to you, given your equipment and your individual tastes. It takes some time and experimentation, but when you have listened to all your options, you’ll know which one is best for you.

  • I’m experiencing a humming or buzzing noise with my subwoofer. What should I check?

    This could be a ground loop hum/buzz or possibly a transformer hum through the speakers. In fact, large subwoofer transformers are more susceptible to a slight hum noise.

    A speaker hum at your listening location is never normal. To determine if the sub amp is functioning correctly, the best thing to do is disconnect all of the connection inputs going into the subwoofer. Keeping the subwoofer plugged into the AC outlet, turn it on; if the hum still exists, there may be a ground loop issue or a problem in the sub amplifier. In that case, the amp should be serviced or replaced. If there is no hum at that point, the issue might involve the preamp or another ‘upstream’ source component. Some common causes of a ground loop hum are cable TV connections, digital recorders or satellite dish receivers.

    If the hum issue is found to be with a cable TV coax wire, then a device called a MAGIC box possibly may help eliminate the ground loop from cable TV, or an OTA antenna. Some, if not all surge protectors have a cable or satellite in and out cable connection; try that as well.

  • I'm not getting any sound out of the subwoofer. What should I check?

    Unplug the system to allow the subwoofer to “reset.” Also, test the speaker using another device. You can plug one end of an audio cable (you may need a RCA female to Mini-plug male adaptor) into the headphone output jack of devices such as a portable CD player or MP3 player; plug the other into either ‘line in’ RCA jacks on the sub to determine if the problem is with the subwoofer or the soundcard drivers. If problems persist, please fill out an online ticketwith our technical support team. 

    Subwoofer Direct CD Test: 

    If you get little or no sound from your subwoofer, perform a "direct in" test to determine if the problem is more than a simple cable or level-setting issue. Start by using a different set of RCA connector cables, then connect the analog audio out from a CD player or DVD player directly into the subwoofer's LINE IN connections. Then, turn the volume level on the subwoofer all the way down. While playing a CD, raise the volume level on the subwoofer; you should hear the bass portion from the source material. If the subwoofer still duplicates the problem, then the issue may be a blown woofer or involve the sub amplifier. However, if the subwoofer functions correctly, then the issue may be with a cable, the receiver and/or a level setting.

  • What is the basic setup for the Quintet™ and optional subwoofer?

    For most home theater systems, you’ll use a standard RCA connector hookup. This is a shielded wire that is similar in construction to the wires leading from a DVD player to a receiver. It will connect to the single SUB or LFE jack on the back of your receiver and to either of the two inputs on the back of the sub. If you wish, you may obtain a ‘Y’ connector to hook up to both of the sub inputs; this will result in a slight increase in volume. 

    Cables specifically designed for subwoofer use typically are better shielded than standard ‘patch cables’ and may offer possible noise reduction or cancellation from electrical devices the cable may come in contact with. Some subwoofer cables are directional, (one end always hooks up to receiver, the other to the sub), so always read any instructions that come with your specialty cabling. 

    Settings in the receiver’s menu system are detailed in the owner’s manual. Here are some suggestions for getting the best possible sound and reliability from your Quintet III with subwoofer system: 

    • Set all speakers to SMALL setting within the speaker setup controls, • Adjust the crossover (or Low Pass filter) to 110 or 120 Hz. 

    • Set the LFE out to SUB ONLY (options might include mains or sub + mains) 

    Settings on the SUB rear panel are as follows: 

    • Set the gain/volume to 8 to begin with; you’ll fine tune the balance with receiver remote control. 

    • Set the low pass/crossover dial fully clockwise to 120. This eliminates the sub’s filter system. 

    • Set the phase switch to ‘0’; you won’t be using this with the Quintet system. 

    • Set the ON/OFF switch near the power cable to ON. This is the master power switch. 

    • Set the auto/ON switch to AUTO. The sub will sense when music or a soundtrack is present and automatically turn the power on. It will wait a few minutes after the end of the movie to shut off. 

    If your receiver came with an ‘optimizer’ microphone and setup system, make sure to check the receiver’s settings after running the auto-setup. It is important that your speakers remain set to the SMALL setting. Quintet III satellite speakers cannot reproduce bass tones; allowing the receiver to send bass to them at movie levels might damage them.

  • The back of the subwoofer is warm. Is this normal?

    A subwoofer will run warm when in use, by design. However, it should not be uncomfortable to leave your hand on the back panel for 5 seconds.

  • What is the basic set up for the Quintet™ III and optional SUB 10 or 12 subwoofer?

    For most home theater systems, you’ll use a standard RCA connector hookup. This is a shielded wire that is similar in construction to the wires leading from a DVD player to a receiver. It will connect to the single SUB or LFE jack on the back of your receiver and to either of the two inputs on the back of the sub. If you wish, you may obtain a ‘Y’ connector to hook up to both of the sub inputs; this will result in a slight increase in volume.

    Cables specifically designed for subwoofer use typically are better shielded than standard ‘patch cables’ and may offer possible noise reduction or cancellation from electrical devices the cable may come in contact with. Some subwoofer cables are directional, (one end always hooks up to receiver, the other to the sub), so always read any instructions that come with your specialty cabling.

    Settings in the receiver’s menu system are detailed in the owner’s manual. Here are some suggestions for getting the best possible sound and reliability from your Quintet III with subwoofer system: 

    • Set all speakers to SMALL setting within the speaker setup controls, 
    • Adjust the crossover (or Low Pass filter) to 110 or 120 Hz. 
    • Set the LFE out to SUB ONLY (options might include mains or sub + mains) 

    Settings on the SUB rear panel are as follows: 

    • Set the gain/volume to 8 to begin with; you’ll fine tune the balance with receiver remote control. 
    • Set the low pass/crossover dial fully clockwise to 120. This eliminates the sub’s filter system. 
    • Set the phase switch to ‘0’; you won’t be using this with the Quintet system. 
    • Set the ON/OFF switch near the power cable to ON. This is the master power switch. 
    • Set the auto/ON switch to AUTO. The sub will sense when music or a soundtrack is present and automatically turn the power on. It will wait a few minutes after the end of the movie to shut off. 

    If your receiver came with an ‘optimizer’ microphone and setup system, make sure to check the receiver’s settings after running the auto-setup. It is important that your speakers remain set to the SMALL setting. Quintet III satellite speakers cannot reproduce bass tones; allowing the receiver to send bass to them at movie levels might damage them.

  • How is the ProMedia 2.1 Wireless considered wireless when I have to use wire to connect the speakers to the subwoofer and then plug it in?

    There are many misconceptions about wireless audio. Often, when people see the words “wireless” and “speakers” together, they assume the entire sound system is wire and cable free. However, no such speaker system exists—unless it runs off of batteries. Speakers need a power source to drive them and that source needs to connect to electricity. 

    With the ProMedia 2.1 Wireless, the subwoofer is the power source. This heavy-hitter plugs into a wall outlet and then the two speakers connect to it via wires. Wireless, in the case of the ProMedia, means no wires attach to the computer. This allows users to move their laptops freely around the room without ever losing their 2.1 sound.

  • Are the satellites magnetically shielded?

    Yes, the satellites are shielded, but the subwoofer is not.

  • Can I use the ProMedia 2.1 Wireless with different wireless speakers?

    No, the USB wireless transmitter that comes with the system only syncs with the ProMedia subwoofer.

  • How should I set my home theater receiver for a particular speaker size?

    The "bass management" option on today's home theater receivers is designed to route mid- or low-bass or both frequencies to a subwoofer in the system. What setting you should select is based on the bass capabilities of the speakers in question.

    In general, "satellite" and bookshelf speakers should be set to "small." Floor-standing speakers should be set to "medium" or "large" depending on their ability to accurately reproduce deeper bass. At the same time this option is set, the frequency of the subwoofer's bass reproduction should also be set. If, for example, you have small bookshelf speakers you have set to "small", you should set your subwoofer to 100-120 Hz. If you have big speakers set to the "large" setting, you should set the subwoofer lower (i.e. 50-80 Hz).

    The correct settings on both the receiver and subwoofer will allow the subwoofer to pick up the bass where the speaker leaves off; creating a smooth transition that reduces boominess at frequencies both the subwoofer and the speaker are delivering. The correct settings are best obtained after experimentation yields the best sound to your ears.

  • What type of software do I need for the ProMedia Wireless 2.1?

    No software is needed. The ProMedia 2.1 Wireless is a plug-and-play design that uses an RF transmitter to shoot the sound signal from the computer to the ProMedia subwoofer.

  • How do I reset the GMX decoder?

    In the unlikely event the GMX decoder needs to be reset (such as a system lockup), you can do so by shutting down the power switch at the rear panel of the subwoofer; wait 30 seconds and turn the power switch back on.

  • How do I re-sync the ProMedia 2.1 Wireless with its wireless transmitter?

    The ProMedia and USB wireless transmitter are synced together when they leave the factory. It’s very rare they would ever become un-synced. However, should it happen, there is a button on the subwoofer and a button on the transmitter that you push to get them in tune again.

  • My Front channels are too loud. Why can't I adjust their levels?

    Due to the nature of the design, unless your speakers are at extremely different distances from the listening position, only minor adjustment should be required. For the system to be set up properly, the center, surrounds, and subwoofer should be adjusted to match the level of the front left and right channels.

  • I’m experiencing a humming or buzzing noise. What should I check?

    This could be a ground loop hum/buzz or possibly a transformer hum through the speakers. In fact, large subwoofer transformers are more susceptible to a slight hum noise.

    A speaker hum at your listening location is never normal. To determine if the sub amp is functioning correctly, the best thing to do is disconnect all of the connection inputs going into the subwoofer. Keeping the subwoofer plugged into the AC outlet, turn it on; if the hum still exists, there may be a ground loop issue or a problem in the sub amplifier. In that case, the amp should be serviced or replaced. If there is no hum at that point, the issue might involve the preamp or another ‘upstream’ source component. Some common causes of a ground loop hum are cable TV connections, digital recorders or satellite dish receivers.

    If the hum issue is found to be with a cable TV coax wire, then a device called a MAGIC box possibly may help eliminate the ground loop from cable TV, or an OTA antenna. Some, if not all surge protectors have a cable or satellite in and out cable connection; try that as well.

  • I hooked up my ProMedia 2.1 Wireless and don't get any sound?

    Make sure your media player software, such as iTunes or Windows Media Player, is not running when you plug in the wireless transmitter.  Once your speakers are synced with the transmitter, launch your media player.

    If trouble persists, try resetting the connection by pushing the "sync" button on the back of the subwoofer, then the button on the wireless transmitter.

    You may be experiencing frequency interference from your wireless router.  You can change the router's frequency with the software provided with the router.

  • Regarding Soundcard connectivity:

    To connect a soundcard's digital output to the GMX system, you may use the included dual RCA to mini plug y adapter.     

    For Soundblaster cards, plug the mini plug end into the S/PDIF output of the card, and the white RCA plug into the Coax In of the GMX decoder.     

    For Turtle Beach Santa Cruz, plug the mini plug end into the S/PDIF output of the card, and the red RCA plug into the Coax In of the GMX decoder.

    Note: When playing an analog signal (mp3s, music CD, PC sounds, etc) through the S/PDIF output, you will hear the front two speakers and subwoofer when the decoder is in stereo mode. Changing the Surround mode to 5CH Stereo or PLII will allow you to listen through all 5 speakers.

  • Can you recommend a repair center for my out-of-warranty/discontinued Heritage grille?

    DuraCrest is a valued Klipsch partner providing assistance with grille repair.  Contact them at:

    DuraCrest Fabrics, Inc.

    2474 Delta LaneElk 

    Grove Village, Il  60007

    Phone: 847-350-0030

    Fax: 847-350-0033

    To learn more about our valued partnership with DuraCrest, check out our blog .

  • I ran the test tones and I am getting sound out of all the speakers, but I still have no surround output outside of the test tones.

    Not all modes or all soundtracks are designed to produce output from all channels. Below is a list of possible reasons for lack of output in a channel or channels.

    During Stereo decoding (no mode LED's lit) the system will only output from the main left and right speaker, and the subwoofer.

    Dolby Digital can be anywhere from 1 (mono) to 5.1 channels. Not all Dolby Digital soundtracks are designed to produce output from all 5 channels. In general, the DVD packaging, or the DVD player On Screen Display should provide an indication of how many channels of information are contained in the soundtrack.

    Some soundtracks may not be surround encoded, and processing these signals with Pro Logic II Music mode or Movie mode may result in output from only the center channel, or no surround output. This does not indicate a problem with the system.

  • I'm only getting sound out of one speaker.

    First, determine if the problem is with the individual speaker by swapping the wire at the back of the satellites. Also, check the speaker wire itself. Swap the wire for the speaker that is working for the one that is dead. If it's the speaker or wire that doesn't work, contact customer service at 800-554-7724. 

    If it's a channel is out, make sure the plug is firmly seated into the soundcard. Also, you can test the speakers with another device (you can plug the audio cable into any headphone output jack of devices such as a portable CD player, walkman, or mp3 player) to determine if the problem is with the subwoofer or the soundcard. If a channel is still out when using the other device as a source, please contact technical support at support@klipsch.com. If the speakers work with the other device, you may need to reinstall your soundcard drivers—contact your soundcard manufacturer for further assistance.

{"apiKey":"5gsk5uyr"}